Key takeaways
- Module (or diametral pitch), number of teeth, pressure angle, helix angle and hand, profile shift and face width define the tooth geometry; diameters alone are not enough.
- State the accuracy class, material, heat treatment, surface hardness and case depth explicitly, otherwise quotations cannot be compared.
- Without a drawing, send the worn gear and, if possible, its mating gear, plus photos, measurements and nameplate data.
- Operating data (power, speed, duty, shock loads) are needed whenever the gear must be designed, upgraded or checked for load capacity.
Why gear data matter in a quotation
A custom gear is defined by far more than its outside diameter and number of teeth. Two gears that look identical can have different modules, pressure angles or profile shifts and will not mesh correctly with the existing counterpart. A complete request lets the manufacturer quote the right process route — gear cutting, heat treatment, grinding, inspection — instead of pricing assumptions. It also shortens the technical clarification that otherwise precedes every offer.
The data below apply to spur, helical, double-helical, bevel, worm and internal gears. Mark clearly what is mandatory (for example the mating geometry) and what may be optimised by the manufacturer.
The data that identify a gear
Tooth geometry
- Gear type — spur, helical, double-helical (herringbone), straight or spiral bevel, hypoid, worm and worm wheel, internal (ring) gear, rack, spline.
- Module m (mm) or diametral pitch DP (1/inch). The conversion is m = 25.4 / DP. Equipment of American or British origin often uses DP or a non-metric pressure angle; say so if you know it.
- Number of teeth z of the gear and, whenever possible, of the mating gear.
- Pressure angle α — 20° is the usual standard; 14.5° appears on older equipment, 25° on some heavy-duty drives.
- Helix angle β and hand of helix (right or left). On parallel shafts, two meshing external helical gears have opposite hands.
- Profile shift coefficient x (addendum modification). If unknown, give the measurements that allow it to be derived: span measurement Wk over k teeth, or dimension over pins/balls, plus tip diameter and centre distance.
- Face width b, and for double-helical gears the width of the central gap.
- Tip diameter, root diameter, bore, keyway or spline in the bore, hub and web dimensions, and axial reference faces.
Accuracy and fit
Specify an accuracy class according to the standard used in your plant: ISO 1328-1, DIN 3961/DIN 3962 or AGMA 2015. Add the tooth thickness allowance or the required backlash (DIN 3967 is common in metric drawings), the bore tolerance (e.g. H7) and the keyway standard. Over-specifying accuracy increases cost without benefit; under-specifying may give a noisy or short-lived gear. When in doubt, state the application and speed and ask for a proposal.
Material, heat treatment and surface finish
- Material with its European designation and material number, for example 18CrNiMo7-6 (1.6587) or 42CrMo4 (1.7225).
- Heat treatment: case hardening (carburizing), nitriding or nitrocarburizing, induction hardening, quench and temper, or none.
- Surface hardness and core hardness, e.g. 58–62 HRC on the flanks.
- Case depth: for carburized gears the case hardening depth CHD (commonly defined at 550 HV, ISO 18203); for induction hardening the hardening pattern (flank only or flank and root, tooth-by-tooth or spin hardening); for nitriding the nitriding hardness depth.
- Finish: hobbed or shaped, or ground after heat treatment; flank roughness Ra if specified.
Our guide on gear materials and heat treatment explains how to choose and specify these values.
Extra data for bevel, worm and internal gears
- Bevel gears: shaft angle (usually 90°), tooth form (straight, spiral, Zerol, hypoid), spiral angle and hand, hypoid offset, mounting distance and whether the pinion and wheel are supplied as a matched, lapped or ground set.
- Worm gear sets: number of starts, axial module, lead angle and hand, centre distance, worm wheel rim material (often bronze) and worm hardness.
- Internal gears: whether the ring is a separate part or integral with a housing, the mounting holes and the mating pinion or planet data.
When there is no drawing
Many requests concern a gear that has failed in an old machine. In that case:
- Send the sample, cleaned and protected against corrosion. If possible send the mating gear too: measuring both gears makes it possible to reconstruct module, profile shift and centre distance with confidence.
- Measure what you can on site: count the teeth; measure the tip diameter (directly for an even number of teeth, with a correction for an odd number); measure the face width; take a span measurement over several teeth with a disc micrometer; measure the centre distance between the shafts in the housing; note the helix hand.
- Take photographs: the complete part, a close-up of the teeth with a ruler for scale, the damaged area, the bore and keyway, and the gearbox nameplate.
- Record the nameplate data: gearbox manufacturer, type, ratio, power, speed and serial number.
- Indicate wear: a worn tooth is thinner than the original. Measure in the least loaded area (often the ends of the face width) and state which flank carried the load.
- Material: a hardness reading on the flank and on the hub is useful. For critical parts a chemical analysis by a laboratory is the only reliable way to identify the steel.
The procedure for rebuilding a drawing from a worn part is described in our guide on reverse engineering of spare parts and on the reverse engineering service page.
Operating data
Operating data are needed whenever the manufacturer must design the gear, change its material or heat treatment, or check that a replacement is adequate. A load capacity calculation according to ISO 6336, DIN 3990 or AGMA 2001/2101 requires at least:
- transmitted power (kW) or torque (Nm) and the speeds (rpm);
- duty: hours per day, start/stop frequency, reversing operation, shock loads (crushers, mills, rolling mills);
- lubrication: oil type and viscosity, splash or forced lubrication, operating temperature;
- environment: dust, water, ambient temperature;
- the application: conveyor drive, mill pinion, crane hoist, extruder gearbox, pump.
If a gear has failed, describe how: our guide on the common causes of industrial gear failure helps to recognise the damage mode.
Quantity, documents and delivery
State the quantity (including spares), whether gears must be supplied as matched pairs, the required inspection documents (material certificate, dimensional report, hardness report, gear measurement report, EN 10204 document type), the marking and packaging, the delivery location and the desired delivery date. A realistic date allows the manufacturer to plan heat treatment and grinding, which often determine the total time.
RFQ checklist
| Item | Why it matters | If unknown, send |
|---|---|---|
| Gear type | Defines the manufacturing route | Photos of the gear and its mating gear |
| Module / DP, number of teeth | Basic tooth size | Sample, tip diameter, centre distance |
| Pressure angle, helix angle and hand | Meshing with the counterpart | Sample or mating gear |
| Profile shift | Tooth thickness and centre distance | Span measurement Wk over k teeth |
| Face width, bore, keyway | Fit on the shaft | Sketch with dimensions |
| Accuracy class, backlash | Noise, load sharing, cost | Application and speed |
| Material | Strength and heat treatment | Hardness readings, old certificate |
| Heat treatment, hardness, case depth | Load capacity and wear | Application and failure history |
| Surface finish / grinding | Contact quality | Accuracy class and speed |
| Power, speed, duty | Rating check or design | Motor and gearbox nameplates |
| Quantity, documents | Price and inspection plan | — |
| Delivery location and date | Planning and transport | — |
Common mistakes
- Giving only the outside diameter and number of teeth. Module and profile shift cannot be separated without more data.
- Confusing module and diametral pitch, or assuming 20° when the original gear has 14.5°.
- Forgetting the hand of helix or the spiral hand of a bevel pinion.
- Replacing one gear of a worn pair. A new gear running against a worn counterpart often wears quickly; consider replacing both.
- Specifying hardness without case depth (or the reverse); both are needed for a case-hardened gear.
- Measuring a worn tooth as if it were new, which leads to wrong tooth thickness and backlash.
- Omitting bore, keyway and axial location, which are as important for assembly as the teeth.
- No accuracy class, or a class far tighter than the application needs.
How TSIRIKOS can help
TSIRIKOS manufactures industrial gears to customer drawings or samples: spur, helical, double-helical, bevel including spiral bevel, worm gear sets and internal gears, as well as pinion shafts and splined parts. Gear cutting, heat treatment, gear grinding and inspection are carried out in-house in Piraeus, Greece. If you have a drawing, see manufacturing from drawings; if you only have a worn part, we can start from the sample.
Send your data, drawings or photos through the request for quotation page. Incomplete information is not a problem: we will tell you what is missing.
Technical FAQ
Can TSIRIKOS quote a gear without a drawing?
Yes. TSIRIKOS manufactures to customer drawings or to samples. Without a drawing, the sample is measured, the tooth geometry is reconstructed and a drawing is prepared for your approval before manufacture. Sending the mating gear as well makes the reconstruction considerably more reliable.
In which format should drawings be sent?
A dimensioned PDF drawing is the minimum. If you have CAD data, add DWG, DXF or STEP files. A gear data table on the drawing (module, teeth, pressure angle, helix angle, profile shift, accuracy class, tooth thickness or span measurement) avoids most technical questions.
I do not know the profile shift. Is that a problem?
No. Few users know it. Give the tip diameter, the centre distance of the mating pair and a span measurement over k teeth (or a measurement over pins/balls); from these values the profile shift can be calculated. On a sample it is determined during measurement.
Which standards are used for gear design and accuracy?
Spur, helical and internal gears are designed and manufactured according to ISO 6336, ISO 1328, DIN 3990 and AGMA standards, among others; bevel gears also to DIN 3971 and DIN 3991, worm gears to DIN 3975 and DIN 3996. Please state the standard and class on your drawing.
Can inspection documents according to EN 10204 be supplied?
Yes. The quality control department issues inspection documents according to EN 10204 (types 2.1, 2.2, 3.1 and 3.2; type 3.2 involves an independent inspector appointed by the purchaser or by regulations). Specify the required document type in your request.
Do you supply gears to customers outside Greece?
TSIRIKOS produces for customers abroad, mainly in North Africa and the Mediterranean. All manufacturing is carried out in Greece; transport, packaging and delivery terms (Incoterms) are agreed for each order.