Industries
Gears and Gearboxes for Cement Plants, Mining and Phosphates
TSIRIKOS repairs gearboxes and manufactures replacement gears, pinion shafts and drive components for mills, crushers, conveyors and other heavy equipment in cement plants, quarries, mines and mineral-processing sites. Parts are made to drawing or from the worn original in our workshops in Piraeus, Greece.
Typical technical challenges
-
Abrasive dust in the oil
Clinker, limestone and ore dust find their way through worn seals and breathers. Contaminated oil causes abrasive wear of tooth flanks and bearings and shortens gearbox life.
-
Continuous duty with shock loads
Crushers, mills and loaded belt conveyors run around the clock. Starts under load and uncrushable material create torque peaks that lead to pitting, tooth breakage and shaft fatigue.
-
Downtime of a whole line
One failed mill or conveyor drive can stop production. Spare gears and shafts must be ready before the planned annual shutdown, not ordered after a breakdown.
-
Ageing installed base
Crushers, conveyor drives and mills often stay in service for decades, long after the original supplier has stopped providing parts or drawings.
How we can support
-
Gearbox repair and overhaul
Learn more : Gearbox repair and overhaulIncoming inspection, dismantling, damage analysis, replacement of gears, shafts and bearings, housing repair, reassembly and gear-mesh check.
-
Conveyor drive gearboxes
Learn more : Conveyor drive gearboxesManufacture and repair of gearboxes for belt-conveyor lines in lignite mines; the same approach applies to conveyor drives in quarries and bulk handling.
-
Reconditioning of mining machinery
Learn more : Reconditioning of mining machineryRepair and reconditioning of mills, dryers, crushers, separators, rollers and conveyors, with gears, gearboxes, shafts and bearings as typical replacement parts.
-
Replacement gears and pinion shafts
Learn more : Replacement gears and pinion shaftsSpur, helical, double-helical and bevel gears and pinion shafts, carburized and ground or induction hardened according to the drawing.
-
Spare parts for earth-moving and quarry equipment
Learn more : Spare parts for earth-moving and quarry equipmentGears, shafts, arms and gearbox parts for loaders, excavators, crushers and drilling machines, including bevel and hypoid sets for axle differentials.
Relevant products
-
Gearboxes & Speed Reducers
Custom parallel-shaft and bevel-helical gearboxes, planetary gear components, gearbox parts, and repair, refurbishment and upgrading of existing industrial gear units. -
Industrial Gears Made to Drawing or Sample
Spur, helical, double-helical, bevel, worm and internal gears, pinion shafts and special gears, made to drawing or sample with in-house gear cutting, heat treatment and grinding. -
Shafts, Pinion Shafts and Splined Shafts
Shafts, pinion shafts, splined shafts and long shafts made to drawing or sample, with in-house gear cutting, heat treatment and grinding. -
Industrial Transmission Components
Couplings, splined hubs, pulleys, sprockets, bushes, rings, worm wheels and Hirth couplings made to drawing or sample to fit your existing drive. -
Industrial Spare Parts Made to Drawing or Sample
Replacement gears, shafts, bushes, pump parts and obsolete OEM components made from drawing or worn sample, for plants in Greece and abroad.
Engineering considerations
Where gears fail in cement and mineral processing
Cement plants and mines combine three loads that gears dislike: continuous duty, shock and contamination. In crushers and conveyor drives the first warning is usually noise, vibration or rising oil temperature; when the gearbox is opened, the typical findings are abrasive wear and pitting on the flanks, worn bearings that have allowed misalignment and, in the worst case, broken teeth. Kiln and mill girth-gear drives add open gearing, where lubrication and alignment between pinion and girth gear decide the service life.
We supply the parts that are replaced in these repairs — gears, pinion shafts and shafts and transmission components such as couplings and bushes — made to drawing or measured from the worn original.
Repair or replace the gearbox?
A housing in good condition with damaged gears and bearings is normally worth repairing: new gears and shafts can be manufactured, bearing seats restored and the unit reassembled with a contact-pattern check. Our gearbox repair and overhaul service covers each step, and the guide Gearbox repair or replacement sets out the decision factors.
Planning around the shutdown
Cement kilns and mineral-processing lines stop for planned maintenance once or twice a year. Spare gears and shafts with long manufacturing times should be ordered against that date: send drawings, nameplate data or samples early, so that technical questions are settled before the outage. Heat treatment — carburizing, induction hardening, quenching and tempering — is done in-house, which keeps the whole manufacturing chain under one roof.
Request a quote with your drawings, photos and quantities.
-
Girth-gear drives of kilns and ball mills
Pinions, pinion shafts and drive gearbox components for girth-gear drives; girth gears are cut within our gear-cutting capacity of up to 4 m outside diameter and module 1 to 20.
-
Elevator, feeder and separator drives
Bucket elevators, apron feeders and separators are usually driven by parallel-shaft or bevel-helical gearboxes — the gearbox families we repair and supply components for.
-
Induction hardening of large gears
Tooth-by-tooth induction hardening of large spur and ring gears is part of our in-house heat treatment.
-
Fix the cause, not only the part
During a repair, check breathers, seals, oil cleanliness and alignment. Otherwise the new gear will fail in the same way as the old one.
Representative images
-
Large helical gears and pinion shafts in the TSIRIKOS yard, ready for dispatch -
Large spur ring gear being induction hardened tooth by tooth with quench spray -
Large double-helical gear on a heavy vertical gear hobbing machine
Technical FAQ
Do you manufacture kiln or mill girth gears?
Girth gears are often several metres in diameter. Whether a particular girth gear can be machined in our workshop depends on its diameter, module, face width and weight, so we assess each case on the drawing. Drive pinions, pinion shafts and gearbox components of girth-gear drives are the type of part we manufacture.
Can you repair a conveyor or crusher gearbox?
Yes. We dismantle and inspect the gearbox, analyse the damage, replace or remanufacture gears, shafts and bearings, reassemble it and check the tooth contact. Each repaired gearbox is documented in a maintenance report.
How can we prepare spare parts for our annual shutdown?
Send drawings or worn samples, nameplate data and quantities well before the shutdown. We review the data, ask the technical questions that matter and quote with a delivery date stated in the offer.
Can you supply parts for equipment outside Greece?
Yes. The company also produces for customers abroad, mainly in North Africa and the Mediterranean. Transport and delivery terms are agreed per order.
What information do you need for a replacement gear?
Gear type, number of teeth, module, pressure and helix angle, outside diameter, face width, bore, material and heat treatment — or the worn gear itself, ideally with its mating gear.
Related pages
Gears and Gearboxes for Cement Plants, Mining and Phosphates
Gearbox repair and replacement gears, pinion shafts and drive parts for mills, crushers and conveyors in cement plants, mines and phosphate processing.
Please attach your technical drawings and specifications to your email.