Industries
Gears, Gearbox Repair and Wear Parts for Steel and Metallurgy
TSIRIKOS manufactures and repairs gears, pinion shafts, gearbox components and machined wear parts for steelworks, rolling mills, tube, profile and wire plants and aluminium extrusion shops. Parts are made to your drawing or from a worn sample in our workshops in Piraeus, Greece.
Typical technical challenges
-
Shock loads in rolling and forming drives
Bar entry, roll changes and cobbles produce torque peaks far above the nominal rating. Gear teeth, pinion shafts and gear couplings in mill drives are exposed to tooth-root fatigue and overload breakage.
-
Heat, scale and abrasive dust
Stands, roller tables and handling equipment work close to hot product and mill scale. Seals, bearings, rolls and lightly loaded open gears wear quickly when contamination gets in.
-
Ageing equipment without drawings
Many mills and forming lines run on machines whose original manufacturer no longer supplies parts. Replacements have to be measured from the worn part and remade.
-
Tooling wear in aluminium extrusion
Dies, liners, dummy blocks and shear knives of extrusion presses work at high temperature and pressure. Their service life depends heavily on the steel grade and on correct hardening.
How we can support
-
Gears and pinion shafts to drawing
Learn more : Gears and pinion shafts to drawingSpur, helical, double-helical and bevel gears and pinion shafts for mill auxiliaries, cranes and conveyors — cut, heat treated and, where specified, ground in-house.
-
Gearbox repair and overhaul
Learn more : Gearbox repair and overhaulDismantling, damage assessment, replacement of gears, shafts and bearings, reassembly and gear-mesh check of drive and crane gearboxes.
-
Forming rolls, pulleys and press parts
Learn more : Forming rolls, pulleys and press partsProfile-forming rolls, split rolls, wire-drawing pulleys, press forming dies and parts for aluminium extrusion presses such as liners/containers, dummy blocks and knives.
-
Heat treatment of extrusion dies
Learn more : Heat treatment of extrusion diesHardening of aluminium extrusion dies and nitrocarburizing of dies and hot-work tooling in our own heat-treatment plant.
-
Replacement parts from a worn sample
Learn more : Replacement parts from a worn sampleWhen no drawing exists, the worn part is measured, the material and heat treatment are defined, and a drawing is prepared for your approval before manufacture.
Relevant products
-
Industrial Gears Made to Drawing or Sample
Spur, helical, double-helical, bevel, worm and internal gears, pinion shafts and special gears, made to drawing or sample with in-house gear cutting, heat treatment and grinding. -
Gearboxes & Speed Reducers
Custom parallel-shaft and bevel-helical gearboxes, planetary gear components, gearbox parts, and repair, refurbishment and upgrading of existing industrial gear units. -
Shafts, Pinion Shafts and Splined Shafts
Shafts, pinion shafts, splined shafts and long shafts made to drawing or sample, with in-house gear cutting, heat treatment and grinding. -
Custom Machined Components to Drawing
Special components machined to drawing — rotors, rings, flanges, drums, housings, dies, propeller parts — with in-house heat treatment and grinding. -
Industrial Spare Parts Made to Drawing or Sample
Replacement gears, shafts, bushes, pump parts and obsolete OEM components made from drawing or worn sample, for plants in Greece and abroad.
Engineering considerations
What steel and metal-forming plants ask of gear parts
Rolling-mill drives, pinion stands, coilers, shears and cranes combine high torque with shock. Double-helical gears are common in heavy mill drives because the opposed helices cancel axial thrust; spur and helical stages dominate auxiliary drives and roller tables; bevel and bevel-helical stages appear wherever the drive turns through 90°. In all of them, failures usually start at the tooth root or on the flanks after a period of overload, misalignment or contaminated oil.
For these parts we work from your drawing or from the worn component. Gears are cut, carburized or induction hardened and ground as specified, and checked for dimensions, hardness and tooth form before dispatch. See our industrial gears and shafts and pinion shafts for the types we produce.
Beyond gears: forming tools and heat treatment
Metal-forming lines also depend on rolls, pulleys, dies and press components that wear against hot or abrasive material. We machine such parts to drawing and heat treat them in-house — carburizing, nitriding, nitrocarburizing, induction hardening, quenching and tempering — so that machining and heat treatment are controlled in one place. More on our heat-treatment services.
When a mill gearbox fails
A failed drive gearbox stops the line. The quickest route back is usually a structured repair: dismantling, damage analysis, replacement of the damaged gears or shafts, new bearings and reassembly with a contact-pattern check. Our gearbox repair and overhaul page explains the steps; the guide to gear failure causes helps you identify the damage before you call.
What to send with your enquiry
- Drawing (PDF, DWG/DXF or STEP) or photos and main dimensions of the worn part
- Gearbox nameplate data, power and speed, if the part belongs to a gearbox
- Material and hardness requirements, if known
- Quantity, target date (for example a planned shutdown) and delivery location
Request a quote with these details and our engineers will review the technical data first.
-
Mill-stand gearboxes and pinion stands
Manufacture and repair of gears and pinion shafts for main mill drives and pinion stands.
-
Large gear cutting capacity
Gear cutting up to 4 m outside diameter and module 1–20.
-
Crane gears
Replacement bevel gears for overhead cranes are among the documented examples of past work.
-
Choosing the heat treatment
Case-hardened and ground teeth for highly loaded stages; quenched and tempered steels for very large wheels where carburizing distortion would be excessive; nitriding where geometry must be kept.
Representative images
-
Large steel ring clamped on the faceplate of a heavy facing lathe -
Large drum on a horizontal boring machine with Heidenhain CNC control -
Induction hardening machine with a large spur ring gear clamped on its rotary table
Technical FAQ
Do you make gears for rolling-mill drives?
We manufacture spur, helical, double-helical and bevel gears and pinion shafts to drawing or sample. Whether a specific mill gear fits our machines depends on its diameter, module, face width and weight — send the drawing or the main dimensions and we will confirm feasibility.
Can you heat treat our aluminium extrusion dies?
Heat treatment for hardening aluminium extrusion dies is part of our heat-treatment services. Send the die steel grade, dimensions and the required hardness or treatment.
Can you repair a crane or roller-table gearbox from a steel plant?
Yes. We dismantle the gearbox, assess the damage, replace or remanufacture gears, shafts and bearings, reassemble it and check the gear mesh. A maintenance report documents the work and the parts replaced.
The OEM no longer supplies the gear. Can you remake it?
Yes, from the worn part and, ideally, its mating gear. We measure the gear geometry, define material and heat treatment with you and prepare a drawing for approval before manufacture.
Which inspection documents can you supply?
Inspection documents according to EN 10204 (types 2.1, 2.2 and 3.1; type 3.2 requires an independent inspector) are agreed with the order.
Related pages
Gears, Gearbox Repair and Wear Parts for Steel and Metallurgy
Gears, pinion shafts, gearbox repair, forming rolls and heat treatment of extrusion tooling for steelworks, rolling mills and metal-forming plants.
Please attach your technical drawings and specifications to your email.