Industries
Plastics and Extrusion: Screws, Barrels and Extruder Gearboxes
Since 1985 TSIRIKOS has manufactured and repaired parts for plastics machinery: extruder screws, barrels and parts for extrusion and injection moulding machines, together with the gears and gearboxes that drive them. Everything is produced to drawing or sample in our workshops in Piraeus, Greece.
Typical technical challenges
-
Abrasive and corrosive compounds
Glass fibre, mineral fillers and recycled feedstock wear flights and barrel bores; PVC and some additives add corrosion. Surface hardness and material choice decide how long a screw lasts.
-
Wear costs output
As the clearance between flight and barrel grows, melt flows back over the flights. Output falls, melt temperature becomes harder to control and energy per kilogram rises.
-
Contaminated recycling feed
Sand, metal and other foreign matter in post-consumer material attack screws, barrels, dies and the knives and rollers of size-reduction machines.
-
High thrust in the drive
Extruder gearboxes carry the full screw-back pressure on their thrust bearing while delivering continuous torque. Bearing and gear damage often show first as noise and temperature rise.
How we can support
-
Extruder screws
Learn more : Extruder screwsSingle screws for extrusion, injection moulding and blown-film lines, machined to drawing or measured from a worn screw, with flights ground to size.
-
Barrels, single and twin
Learn more : Barrels, single and twinBarrels (cylinders) for single-screw and twin-screw extruders, and valve heads, made of high-strength steels.
-
Screw and barrel reconditioning
Learn more : Screw and barrel reconditioningRemoval of damaged material, build-up with new material, machining to nominal dimensions and roughness, then nitriding or nitrocarburizing.
-
In-house nitriding and nitrocarburizing
Learn more : In-house nitriding and nitrocarburizingGas nitriding and nitrocarburizing of screws and barrels in our own heat-treatment plant, for a hard, wear-resistant surface with low distortion.
-
Parts for recycling lines
Learn more : Parts for recycling linesScrews, barrels and dies for polymer regeneration, plus knives, gearboxes and rollers for size-reduction machinery.
-
Extruder gearbox repair
Learn more : Extruder gearbox repairDismantling, inspection, replacement of gears, shafts and bearings, reassembly and gear-mesh check of extruder drive gearboxes.
Relevant products
-
Extruder Screws and Barrels
Extruder and injection screws, single and twin barrels, valve heads and dies, made to drawing or sample, nitrided in-house and reconditioned when worn. -
Gearboxes & Speed Reducers
Custom parallel-shaft and bevel-helical gearboxes, planetary gear components, gearbox parts, and repair, refurbishment and upgrading of existing industrial gear units. -
Industrial Gears Made to Drawing or Sample
Spur, helical, double-helical, bevel, worm and internal gears, pinion shafts and special gears, made to drawing or sample with in-house gear cutting, heat treatment and grinding. -
Shafts, Pinion Shafts and Splined Shafts
Shafts, pinion shafts, splined shafts and long shafts made to drawing or sample, with in-house gear cutting, heat treatment and grinding. -
Industrial Spare Parts Made to Drawing or Sample
Replacement gears, shafts, bushes, pump parts and obsolete OEM components made from drawing or worn sample, for plants in Greece and abroad.
Engineering considerations
Screws and barrels since 1985
Plastics machinery has been part of our work since 1985. Screws and barrels are long, slender parts that combine precise geometry with a hard, wear-resistant surface: the flights must be concentric with the shank, the barrel bore straight and round, and both must survive abrasive and sometimes corrosive melt. We machine screws on long-bed lathes with steady rests, grind the flight diameters, and harden the surface by gas nitriding or nitrocarburizing in our own heat-treatment plant. See extruder screws and barrels for the product range.
Repair or new screw?
A worn screw is not always scrap. If the core is sound, the flights can be built up, re-machined to nominal size and re-nitrided — usually a better option when the original design works well but the supplier is gone or slow. If the barrel bore is also worn, both parts are measured together so that the new clearance is right. The industrial mechanical repair page describes our reconditioning work; when there is no drawing, reverse engineering is the starting point.
The drive side
Behind every extruder is a gearbox carrying high torque and the screw’s axial thrust. We repair these gearboxes and manufacture their gears and shafts, so that screw, barrel and drive can be handled by one supplier.
Recycling lines
Recycling extruders and size-reduction machines face the harshest feed. Screws, barrels and dies for regeneration lines, and knives, rollers and gearboxes for crushers, are among the spare parts we supply.
Request a quote with your drawing or the worn screw’s dimensions.
-
Measure wear before you order
Record the flight outside diameter along the screw and the barrel bore at several positions. The resulting clearance shows whether the screw, the barrel or both need work.
-
Screw and barrel grinding
Cylindrical grinding of extruder screws and grinding of barrels are part of our grinding services.
-
Twin-screw elements and splined shafts
Manufacture of segmented twin-screw elements and their splined shafts.
-
Bimetallic barrels and hardfacing
Bimetallic barrel liners, hardfacing of flight lands and hard chrome plating, carried out in-house or through partners.
Representative images
-
Long extruder screw machined on a long-bed lathe with steady rests -
Extruder screw being ground on a cylindrical grinding machine with coolant spray -
Extruder screws with mixing section, keyed drive shank and cored screw ends -
Extruder screws, helical gear and shafts suspended on a fixture above a pit furnace
Technical FAQ
What data do you need to quote an extruder screw?
Screw diameter D, length or L/D ratio, flight geometry (pitch, flight depth per zone, compression ratio), mixing sections, drive shank, material and surface treatment, the polymer processed — or the worn screw itself and the barrel bore dimensions.
Can you recondition a worn screw instead of replacing it?
Often, yes. Damaged material is removed, the flights are built up, machined back to nominal dimensions and roughness, and the screw is nitrided or nitrocarburized. Whether reconditioning is worthwhile depends on the wear and the condition of the core.
Do you make parts for twin-screw extruders?
Barrels for twin-screw extruders are among the parts we have produced. For screw elements and splined shafts, send the drawing or sample and we will confirm feasibility.
Do you work on injection moulding machines?
Yes. We manufacture and repair plasticating screws, barrels and related parts for injection moulding machines, as well as parts for blown-film extrusion.
Can you repair the extruder gearbox as well?
Yes. Extruder drive gearboxes are repaired like other industrial gearboxes: inspection, dismantling, new gears, shafts or bearings as needed, reassembly and gear-mesh check.
Related pages
Plastics and Extrusion: Screws, Barrels and Extruder Gearboxes
Extruder screws and barrels, screw and barrel reconditioning, nitriding and extruder gearbox repair for plastics processors and recycling lines.
Please attach your technical drawings and specifications to your email.