Industries
Power Generation: Gears, Gearbox and Pump Repair for Power Plants
TSIRIKOS repairs gearboxes and manufactures gears, shafts and pump parts for power-generation plants — steam, diesel and hydroelectric — working to drawing or from the worn component in its workshops in Piraeus, Greece.
Typical technical challenges
-
Availability comes first
An outage of a main or auxiliary drive costs generation. Coal mills, fans, pumps and fuel-handling conveyors must run between planned overhauls.
-
High speeds and tight tolerances
Turbine-driven gear units and pump drives run at high pitch-line velocities. Tooth accuracy, flank finish and balance decide noise, vibration and service life.
-
Variable and cyclic loads
Hydro turbines, diesel generators and wind turbines see frequent load changes. Micropitting, pitting and bearing damage are the typical consequences.
-
Pumps under wear
Cooling-water, feed and lubricating-oil pumps suffer wear of gears, shafts and bushes. Replacement parts must restore the original clearances.
How we can support
-
Power-plant gearbox repair
Learn more : Power-plant gearbox repairRepair of gearboxes, gears, shafts and bearings for steam, diesel and hydroelectric plants: inspection, dismantling, damage analysis, remanufacture, reassembly.
-
Pump repair and pump parts
Learn more : Pump repair and pump partsRepair of pumps and manufacture of pump gears, shafts and bushes, including gear pumps and oil-pressure pumps.
-
Carburized and ground gears
Learn more : Carburized and ground gearsSpur and helical gears gas carburized, hardened and finish-ground on gear-grinding machines for accurate tooth form, good surface finish and quiet running.
-
Turbine gears
Learn more : Turbine gearsGears for turbine drives are among the products the company has manufactured.
-
Shafts and journals
Learn more : Shafts and journalsManufacture of new shafts, or repair of worn journals by grinding, welding or metallizing followed by final grinding.
Relevant products
-
Gearboxes & Speed Reducers
Custom parallel-shaft and bevel-helical gearboxes, planetary gear components, gearbox parts, and repair, refurbishment and upgrading of existing industrial gear units. -
Industrial Gears Made to Drawing or Sample
Spur, helical, double-helical, bevel, worm and internal gears, pinion shafts and special gears, made to drawing or sample with in-house gear cutting, heat treatment and grinding. -
Shafts, Pinion Shafts and Splined Shafts
Shafts, pinion shafts, splined shafts and long shafts made to drawing or sample, with in-house gear cutting, heat treatment and grinding. -
Industrial Transmission Components
Couplings, splined hubs, pulleys, sprockets, bushes, rings, worm wheels and Hirth couplings made to drawing or sample to fit your existing drive. -
Industrial Spare Parts Made to Drawing or Sample
Replacement gears, shafts, bushes, pump parts and obsolete OEM components made from drawing or worn sample, for plants in Greece and abroad.
Engineering considerations
Gear drives in power plants
A power plant contains far more gearing than its main turbine train: coal-mill drives, fuel and ash conveyors, fans, cooling-tower drives, pumps and, in hydro plants, gate and governor mechanisms. Diesel plants add engine-driven pumps and auxiliary drives. Most of these are parallel-shaft, bevel-helical or planetary gearboxes running continuously between planned overhauls.
When such a unit fails, the decision is between waiting for an OEM exchange unit and repairing the existing one. Repair is often quicker when the housing is sound: we manufacture new gears and shafts, restore bearing seats and reassemble the gearbox with a contact-pattern check. The steps are described on our gearbox repair and overhaul page.
Precision where speed is high
High-speed stages need accurate, hard and smooth tooth flanks. Our gears for such duties are case-hardened by gas carburizing and then ground, so that distortion from heat treatment is removed and the flank finish is controlled. Carburizing, nitriding and induction hardening are performed in our own heat-treatment plant.
Pumps
Gear pumps, oil-pressure pumps and other plant pumps wear at gears, shafts and bushes. We repair pumps and manufacture these parts to restore the original clearances — see industrial mechanical repair.
Before the outage
Send nameplate data, power and speed, photos or drawings of the damaged parts and, if available, oil-analysis and vibration reports. The guide to gear failure causes helps you describe the damage. Then request a quote.
-
Wind-turbine gearboxes
Repair of wind-turbine gearboxes (speed-increasing gearboxes) and their gears.
-
Back-to-back test rig
Repaired gearboxes can be tested on the company’s back-to-back gearbox test rig with vibration, temperature and noise monitoring.
-
Test rig power
Back-to-back testing up to 9,000 kW.
-
Maintenance report
Each repaired gearbox is documented: type and serial number, work carried out and parts replaced or repaired.
Representative images
-
Planetary gear set with ring gear, three planet gears and splined sun shaft -
Gear pump body with two meshing spur gears -
Measuring tooth-flank roughness of a helical gear with a portable roughness tester
Technical FAQ
Which power-plant equipment do you work on?
Gearboxes, gears, shafts, bearings and pumps of steam, diesel and hydroelectric power plants — both the main drives and auxiliary equipment such as fans, mills, conveyors and pumps.
Do you repair wind-turbine gearboxes?
Please contact us with the gearbox data. We will tell you which parts of the work — gears, shafts, bearing seats, housings — we can carry out for your unit.
Can you grind gears after heat treatment?
Yes. Spur and helical gears are gas carburized, hardened and then ground on gear-grinding machines to correct the tooth form after heat-treatment distortion.
Can a repaired gearbox be tested before delivery?
Repaired gearboxes can be load-tested on our back-to-back test rig; temperatures, vibration and noise are checked. The test scope is agreed with the order.
What should we send before a planned outage?
Nameplate data, power and speeds, drawings or photos of the damaged parts, the oil-analysis or vibration report if available, and the outage dates.
Related pages
Power Generation: Gears, Gearbox and Pump Repair for Power Plants
Repair of gearboxes, gears, shafts, bearings and pumps for steam, diesel and hydroelectric power plants, with in-house gear grinding and heat treatment.
Please attach your technical drawings and specifications to your email.