Industries

Rail: Spare Parts for Rolling Stock and Rail Equipment

TSIRIKOS manufactures mechanical spare parts for rail vehicles — gears, shafts, arms and bushes for diesel engines, braking systems, traction and pumps — to drawing or from the worn original, in its workshops in Piraeus, Greece.

Bush trued in a four-jaw lathe chuck with two dial indicators

Typical technical challenges

  • Safety-relevant parts

    Brake, traction and running-gear parts affect safety. Materials, heat treatment and inspection must be documented and traceable, and the vehicle owner decides on approval.

  • Long vehicle life

    Locomotives, railcars and track machines stay in service for decades. Parts for older series are often no longer available from the original supplier.

  • Shock and high cycle counts

    Traction gears and axle-mounted components see impact loads from the wheel–rail contact and millions of load cycles; tooth-root fatigue and flank pitting are typical failure modes.

  • Depot schedules

    Maintenance depots plan overhauls by mileage or time. Replacement parts need to be available when the vehicle comes in, not after it has been stripped.

How we can support

Engineering considerations

Mechanical parts for rail vehicles

Rail vehicles contain many mechanical parts that wear long before the vehicle is retired: gears and shafts in diesel engines and their auxiliary drives, levers, arms and bushes in brake rigging, pump gears and shafts, and the gears, pinions and couplings of traction drives. When a series is old or produced in small numbers, original parts become hard to source.

We manufacture such parts to the operator’s drawing or from a worn sample. Shafts and pinion shafts are turned, heat treated and ground; gears are cut, hardened and, where required, ground; bushes and arms are machined to the specified fits. All heat treatment is carried out in our own heat-treatment plant.

From worn part to approved drawing

Many rail spare-part requests start without a drawing. The method is to measure the worn part, determine its geometry and material, define the heat treatment and produce a drawing that the operator approves before manufacture. Our reverse engineering service and the guide Reverse engineering of mechanical spare parts explain each step and its limits.

What to send

  • Drawing, or photos and main dimensions of the worn part
  • Vehicle type and the assembly the part belongs to
  • Material, hardness and any standard named on the drawing
  • Quantity, required documentation and delivery location

When a drawing exists, see manufacturing from drawings. Then request a quote.

  • Traction gear sets

    Manufacture of traction gear and pinion sets for locomotives and railcars.

  • Track maintenance machines and workshop equipment

    Gears, shafts and gearbox repair for track maintenance machines and depot equipment.

  • Approval stays with the vehicle owner

    Parts made to drawing or sample for vehicles in service must be approved by the operator or the entity in charge of maintenance; we supply the drawing, material data and inspection documents needed for that decision.

  • Inspection documents

    Inspection documents to EN 10204 (2.1, 2.2, 3.1, and 3.2 with an independent inspector) can be agreed with the order.

Technical FAQ

Which rail parts can you manufacture?

Gears, shafts, arms and bushes for diesel engines, braking systems, traction and pumps of rail vehicles, made to drawing or from the worn part. Send the drawing or photos and we will confirm feasibility.

Can you remake an obsolete part without a drawing?

Yes. We measure the worn part, determine the gear or shaft geometry, agree material and heat treatment with you and prepare a drawing for your approval before manufacture.

Are your parts approved for rail vehicles?

Approval of a non-OEM part for a vehicle in service is the decision of the operator or maintenance entity. We provide the drawing, material certificates and inspection results needed for that approval.

Which materials and treatments do you use?

As specified on the drawing — typically case-hardening, through-hardening or nitriding steels, with carburizing, induction hardening, nitriding or quenching and tempering performed in-house.

Rail: Spare Parts for Rolling Stock and Rail Equipment

Gears, shafts, arms and bushes for diesel engines, braking systems, traction drives and pumps of rail vehicles, made to drawing or from a sample.

Please attach your technical drawings and specifications to your email.