Technical guide

Gearbox Repair or Replacement: Technical Considerations

Most industrial gearboxes can be repaired; the right decision depends on the condition of the housing, the damage to gears and bearings, the availability of parts and the cost of downtime. This guide explains how to recognise problems early, how a gearbox is inspected, and how to decide between repair, upgrade and replacement.

Disassembled heavy industrial gearbox with helical and bevel gear stages

Key takeaways

  • Noise, vibration, temperature rise, oil analysis results and leaks are early warnings; trend them instead of waiting for a breakdown.
  • The housing is the key item: if bearing bores and split faces are sound or can be restored, repair is usually the most economical option.
  • Gears and shafts can be re-manufactured to drawing or sample, often with improved material, heat treatment or grinding.
  • A repair is complete only after a run test, a contact pattern check and a written record of the work and the replaced parts.

Repair or replace: the question behind the question

When a gearbox fails, the real question is not only “repair or replace?” but “what restores reliable operation fastest, at an acceptable risk and cost?”. A new catalogue gearbox may not fit the existing foundation, shafts and couplings; an original spare may no longer be available; a special gearbox designed for the machine may be the only option. Conversely, a repair that ignores the root cause will fail again. A structured approach — symptoms, inspection, decision, repair, test, documentation — avoids both mistakes.

Symptoms that call for an inspection

  • Noise: a new whining tone usually points to gear mesh problems (wear, pitting, misalignment); rumbling or irregular knocking points more often to bearings or broken teeth.
  • Vibration: rising amplitudes at gear mesh frequency, sidebands around it, or bearing defect frequencies. Trends are more useful than single values; ISO 20816 (formerly ISO 10816) gives the general framework for evaluating machine vibration.
  • Temperature: a rise in oil sump or bearing temperature at unchanged load indicates friction, lubrication problems or preloaded bearings.
  • Oil analysis: increasing iron and other wear metals, particle counts (cleanliness code according to ISO 4406), water content, viscosity change or oxidation. Large flakes found by ferrography or on magnetic plugs are a strong warning.
  • Leaks: worn seals, damaged shaft sleeves, blocked breathers that pressurise the housing, or cracked housings.
  • Operational signs: shaft movement, coupling wear, loose foundation bolts, frequent oil top-ups.

How a gearbox is inspected

Before opening

Record the nameplate data, operating hours and recent events (overloads, power cuts, lubrication incidents). Take an oil sample before draining. Check breather, seals, external damage, foundation and alignment of couplings. Where possible, measure vibration and temperature under load; a borescope through the inspection cover can show tooth condition without dismantling.

After dismantling

  1. Clean and examine every gear: contact pattern, wear, pitting, micropitting, scuffing, cracks, broken teeth. Our guide on common causes of industrial gear failure describes how to recognise each mode.
  2. Crack detection on highly stressed areas (tooth roots, shaft shoulders, keyways) by magnetic particle or dye penetrant testing.
  3. Hardness checks on gear flanks to detect softening or incorrect heat treatment.
  4. Bearings: raceway damage, clearance, fit on shaft and in housing.
  5. Shafts: journal and seal diameters, runout, keyway condition, signs of fretting.
  6. Housing: bearing bore diameters and roundness, bore alignment and centre distances, flatness of the split face, cracks.

The result should be a written damage assessment with photographs, the probable root cause and a list of parts to replace, re-manufacture or reuse.

Decision factors

  • Housing condition. If the bores and centre distances are within tolerance or can be restored by re-boring and sleeving, the main argument for replacement disappears.
  • Damage mode and extent. Localised wear or bearing failure is usually repairable; a shattered housing or a broken shaft caused by a severe overload may justify replacement — but the overload must be understood in either case.
  • Availability of original parts. For older gearboxes, OEM spares may be obsolete or have long delivery times. Gears and shafts can then be re-manufactured from samples or drawings.
  • Time. Compare the realistic time for the repair with the delivery time of a new unit and the time needed to adapt foundations, couplings and guards.
  • Cost of downtime. On a kiln drive, mill or conveyor in continuous operation, the production loss often outweighs the price of the gearbox itself. Keeping critical spares (gear sets, shafts, bearings) can be the most effective decision.
  • Upgrade opportunity. If the original design is marginal for the present load, a repair can include better materials, case-hardened and ground gears, or bearings with higher load ratings.
  • Recurring failures. Repeated failures of the same component point to a design or application problem that a like-for-like replacement will not solve.

Repair options

Gears and shafts

  • Re-manufacture of gears and pinions to the original geometry, measured on the sample, or to an improved design. Worn gear pairs are normally replaced as a pair.
  • Replacement of a toothed rim on a large wheel whose hub and web are sound.
  • Shaft repair of worn journals and seal seats by grinding, by welding or metallizing and final grinding — or a new shaft when the damage is in a highly stressed zone.

Housing

  • Re-boring and sleeving of worn bearing bores, restoring diameters and centre distances.
  • Weld repair of cracks, followed by machining of the affected faces.
  • Machining of the split face to restore flatness and sealing.

Bearings, seals and lubrication

  • New bearings, if possible of types with higher load ratings in the same envelope.
  • New seals and, where shafts are worn, sleeves or modified seal seats.
  • Clean breathers, correct oil type and level, and, if needed, improved lubrication or filtration.

The gearbox repair and overhaul page describes the corresponding workshop process.

Testing after repair

A repaired gearbox should be verified before it returns to service:

  • Contact pattern check with marking compound on each stage during assembly; adjust shims or bearing settings as needed.
  • Backlash and bearing clearances measured and recorded.
  • Run test without load and, where the means exist, under load: temperature stabilisation of oil and bearings, noise, vibration, leaks.
  • Final inspection of the external condition, painting, oil filling or preservation for storage and transport.

Documentation

Ask for a repair report that records: gearbox type and serial number, condition as received (with photos), damage assessment and probable cause, work carried out, parts replaced or re-manufactured (with material and heat treatment), measured clearances and contact patterns, test results and recommendations for operation and monitoring. This record is the reference for the next inspection and for the purchase of future spares.

Decision table

Situation Usually Notes
Worn or pitted gears, housing sound Repair Replace gears in pairs; check alignment and lubrication
Bearing failure, no secondary damage Repair Find the cause: lubrication, contamination, fit, overload
Worn bearing bores Repair Re-bore and sleeve; restore centre distances
Broken tooth or shaft after overload Repair or replace Depends on housing; understand the overload first
Cracked housing Case by case Weld repair possible if the crack is not in a bearing bore
OEM parts obsolete or slow to obtain Repair with re-manufactured parts Reverse engineering from samples
Recurrent failures of the same part Upgrade or redesign A like-for-like repair will fail again
Load or ratio must change New design or replacement Check the existing foundation and connections

Preparing a repair request

The decision is faster when the workshop receives the right information from the start:

  • nameplate data (manufacturer, type, ratio, input power and speed, serial number) and, if available, the original drawings or parts list;
  • application and duty: driven machine, hours per day, starts, shock loads;
  • symptoms and their history: when the noise, vibration or temperature rise began, oil analysis reports, vibration trends;
  • photos of the installed gearbox, of any visible damage, and of the shaft ends and couplings;
  • the scope you expect: inspection and quotation only, repair to original condition, or repair with upgrade;
  • constraints: required date back in service, availability of a spare unit, transport and delivery location.

Where a spare gearbox exists, it can be overhauled first and exchanged at a planned shutdown; the failed unit is then repaired without production pressure and becomes the next spare. For a critical drive without a spare, ordering the long-lead parts (large gears, special shafts) as soon as the damage assessment is available usually saves the most time.

How TSIRIKOS can help

TSIRIKOS repairs and overhauls industrial gearboxes and manufactures new custom gearboxes and speed reducers. Gears, pinion shafts and shafts are re-manufactured in-house to drawing or sample, with heat treatment, gear grinding and inspection in our Piraeus workshop. When no drawings exist, see reverse engineering; for single replacement gears, see industrial gears.

To discuss a damaged gearbox, send the nameplate data, photos of the damage and a description of the symptoms through the request for quotation page.

Technical FAQ

Does TSIRIKOS repair gearboxes made by other manufacturers?

Yes. TSIRIKOS repairs and overhauls industrial gearboxes regardless of the original maker. Worn gears, shafts and other parts are re-manufactured from the original parts or from drawings when spare parts are not available.

Do I receive a report after the repair?

Yes. A maintenance report is provided for every repaired gearbox, recording the gearbox type and serial number, the work carried out and the parts replaced or repaired.

Is the gearbox tested after repair?

After reassembly the gear mesh is checked and a functional check is carried out. The company also operates a back-to-back gearbox test rig with vibration, temperature and noise analysis and lubricant cleanliness monitoring.

What happens to the used oil?

The lubricant drained from the gearbox is disposed of through an authorised recycling body.

Can you inspect a gearbox at our plant outside Greece?

Yes. We carry out on-site inspections outside Greece, arranged case by case for each project. Repairs themselves are done in our workshop in Piraeus, so the gearbox or the damaged parts are shipped there.

Can a repaired gearbox be better than the original?

Often yes, within the limits of the housing: gears can be made in a better steel, case-hardened and ground, bearings can be changed to types with higher load ratings in the same envelope, and seals and breathers can be upgraded. Any change to the gear geometry requires a check of the complete stage.

Request for quotation

Symptoms, inspection, decision factors and repair options for industrial gearboxes, with a decision table to choose between repair, upgrade and replacement.

Please attach your technical drawings and specifications to your email.